Aqua36 C Hydroponic Propagation System – 60 × 40 cm

36 planting positions for propagation and cultivation in nutrient solution. Aqua36 C includes clay granules and 300 g of starter fertiliser plus aeration with a pump, hose and air stone.

1. Position the system

   Position the reservoir level. Insert the water-level indicator into the lid from below and fit the lid.

2. Prepare the pots

   Prepare the 36 pots outside the system with clay granules and suitable plants. Rinse with clean water before inserting them to remove loose particles.

3. Prepare nutrient solution

   Measure 1 g of starter fertiliser per litre of water, for example 10 g per 10 L. Dissolve while stirring for 2–3 minutes. At this dose, 300 g makes 300 L.

4. Set up aeration

   Set up and operate the supplied pump, hose and air stone strictly according to its included original instructions. The exact pump model may vary.

5. Monitor the crop

   With aeration operating, set the water level according to the system instructions up to the maximum mark, approximately 12 L in the standard system. Use 12 g starter fertiliser for 12 L. Check water level, aeration and crop requirements regularly.

6. Replace water and clean

   With aeration, replace the water after approximately 4 weeks. Clean the reservoir regularly, at least every 4 weeks, with water or neutral soap. Maintain the pump according to its original instructions.

Item code

Aqua36-C

Contents

Water reservoir, hinged cover, 36 plant pots, water-level indicator, 2.5 L clay granules, 300 g starter fertiliser, pump, connecting hose and air stone. Pump model may vary; the matching original instructions are included with each unit. Plants not included.

Footprint

60 × 40 cm

Starter fertiliser

NPK(MgO,SO₃) 14–10–14 (+2+30)

Declaration

14% total nitrogen (N): 4% nitrate nitrogen, 10% ammonium nitrogen.

Declaration

10% water-soluble phosphate (P₂O₅); 14% water-soluble potassium oxide (K₂O).

Declaration

2% water-soluble magnesium oxide (MgO); 30% water-soluble sulphur trioxide (SO₃).

Declaration

0.01% water-soluble boron (B) as boric acid; 0.001% water-soluble molybdenum (Mo) as ammonium molybdate.

Declaration

0.02% copper (Cu), 0.05% iron (Fe), 0.05% manganese (Mn), 0.02% zinc (Zn), each water-soluble and chelated by EDTA.

Declaration

Low in chloride. Chelate stability at pH 3–7. Net mass of starter fertiliser: 300 g.

Match light, temperature and nutrient demand to the crop. Check water level and root condition regularly. No fixed unattended supply duration is promised.

At 25 °C, 1 g/L starter fertiliser increases EC by approximately 1.6 mS/cm; this is not a universal target independent of the source water. A 1:10 stock solution in distilled water has pH 4.0 at 25 °C.

• Apply fertiliser according to actual requirements; do not exceed application rates. Intended for horticultural soil and foliar fertilisation.
• General label range outside the Aqua starting programme described here: liquid feeding 0.5–4 ‰, foliar feeding 0.5–2 ‰, according to growth stage and tolerance. The Aqua starting dose is 1 g/L.
• German Hazardous Substances Ordinance: ammonium nitrate, Group C III.
• Keep water-bearing systems away from electrical installations; escaping water must not reach electrical equipment.
• Follow the included original instructions for electrical installation, operation and maintenance of the pump actually supplied.

Store starter fertiliser dry and dark, above 8 °C and no higher than 38 °C, out of reach of children and animals.

Clean the system after the crop. See the application section for routine cleaning.